Mazda3/Mazdaspeed3 General/Maintenance Discussion of the Mazda3 and MazdaSpeed3

'08 3 with p0791 trans code

Old Jun 7, 2016 | 08:38 AM
  #1  
xrjoe's Avatar
Thread Starter
Registered User
 
Joined: Sep 2015
Posts: 10
xrjoe is an unknown quantity at this point
'08 3 with p0791 trans code

intermediate shaft speed sensor circuit, im not finding anything pointing to a relative fix, engine stalls, runs rough intermittently, and dosent seem to shift well, where is this sensor located, im wondering if its connection related. 5 speed auto.
Old Jun 10, 2016 | 05:58 AM
  #2  
aussiblue's Avatar
Registered User
 
Joined: Jun 2016
Posts: 51
From: Bibra Lake Western Australia
aussiblue is an unknown quantity at this point
This help DIY: Mazda 3 (2.3 GT) Turbine/Input Speed Sensor Replacement
Old Jun 10, 2016 | 07:51 AM
  #3  
xrjoe's Avatar
Thread Starter
Registered User
 
Joined: Sep 2015
Posts: 10
xrjoe is an unknown quantity at this point
I pulled the turbine input speed sensor to inspect and confirm good connection, thanks for the link, im guessing the intermediate shaft sensor is the described rear lower sensor?
Old Jun 10, 2016 | 07:11 PM
  #4  
aussiblue's Avatar
Registered User
 
Joined: Jun 2016
Posts: 51
From: Bibra Lake Western Australia
aussiblue is an unknown quantity at this point
Yes; see Mazda 3 S 2006 Mazda3. Transmission slips from 5th to 3rd, scroll down and you'll eventually find pictures.
Old Jun 15, 2016 | 09:00 PM
  #5  
xrjoe's Avatar
Thread Starter
Registered User
 
Joined: Sep 2015
Posts: 10
xrjoe is an unknown quantity at this point
I ordered a repair cd and it dosent cover this trans code, so I went to the dealer and just ordered the part, their parts diagram dosent show this part that well, they couldn't tell if it had 3 wires.
Old Jun 16, 2016 | 05:08 PM
  #6  
xrjoe's Avatar
Thread Starter
Registered User
 
Joined: Sep 2015
Posts: 10
xrjoe is an unknown quantity at this point
it was the right part, lasted 6 drive cycles and reset p0791, im in need of a wiring diagram for the 5 speed auto, with pcm connector/wire identification, or a place I can get a manual
Old Jun 16, 2016 | 09:10 PM
  #7  
aussiblue's Avatar
Registered User
 
Joined: Jun 2016
Posts: 51
From: Bibra Lake Western Australia
aussiblue is an unknown quantity at this point
2003 2008 Mazda 3 Ultimate Factory Service Repair Workshop Maintenance Manual | eBay or similar
Old Jun 16, 2016 | 09:32 PM
  #8  
xrjoe's Avatar
Thread Starter
Registered User
 
Joined: Sep 2015
Posts: 10
xrjoe is an unknown quantity at this point
so this is a real factory manual, covering wiring for trans?
Old Jun 16, 2016 | 10:40 PM
  #9  
aussiblue's Avatar
Registered User
 
Joined: Jun 2016
Posts: 51
From: Bibra Lake Western Australia
aussiblue is an unknown quantity at this point
Yes I assume so; as they state "This is a complete Factory Service Manual ". The pics also look like those in the factory manual I have for the later BL mode. You are lucky LHD manuals both factory and aftermarket are readily available but I have nor been able to get one for the RHD model as sold in Japan, Australia (where I am and UK); even the Australian published Gregory's one is simply the Chilton's with gallons and miles changed to litres and km; they haven't even reversed the pictures use and don't cover the few bits that different in the RHD models.


BTW other causes of this code include low or dirty ATF, solenoid malfunction or valve body failure. I would start by checking the colour and level of the transmission fluid.
Old Jun 17, 2016 | 08:10 AM
  #10  
xrjoe's Avatar
Thread Starter
Registered User
 
Joined: Sep 2015
Posts: 10
xrjoe is an unknown quantity at this point
awesome, fluid is well maintained every 40k, level good, ive also got Mitchell online to purchase information, but its for a short term "per vehicle specific" and id rather have a print or cd copy, ill post my confirmation, thanks aussi !
Old Jun 18, 2016 | 11:48 PM
  #11  
xrjoe's Avatar
Thread Starter
Registered User
 
Joined: Sep 2015
Posts: 10
xrjoe is an unknown quantity at this point
he emailed back not sure
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Canso
Mazda3/Mazdaspeed3
0
Jan 16, 2012 11:14 PM
Tenshi_Akira
Mazda3/Mazdaspeed3
0
Jan 10, 2010 11:52 PM
majorhavoc
3rd gen Engine/Drivetrain
5
May 16, 2007 06:04 PM
rkives
1st gen/323/GLC Engine and Drivetrain
3
Apr 20, 2002 12:08 AM
Bolock
Forced Induction/Nitrous
5
Nov 7, 2001 09:40 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Thread Tools
Search this Thread

All times are GMT -5. The time now is 08:45 AM.