totally bypass the mass air flow sensor...
#3
is there any way i could still install my cold air intake without bypassing my maf....
has anyone done this mod...
like could i just leve the flow meter box and take the old filter out then put my cone in and rout a duct to under my bumper...
any tips or anything would be helpful
has anyone done this mod...
like could i just leve the flow meter box and take the old filter out then put my cone in and rout a duct to under my bumper...
any tips or anything would be helpful
#4
Braden had a CAI on the turboge when it was still NA. I dunno if it's custom fab or what... MAF still in place...
There's a pic on this page:
http://webpages.charter.net/sector323/rc.htm
There's a pic on this page:
http://webpages.charter.net/sector323/rc.htm
#5
thanks for the replies yo......but
HOW DID YOU MOUNT THE CONE ONTO THE FLOW METER LIKE THAT...IT HAS A SQUARE OPENING....
Yeah , i ment a cold air intake....but i'm just trying to throw the cone filter on now...
i'm making a custom cai..but it will take me a while to get the supplies i need...i'm making it with a short civic intake tube or a weapon r.....because both can fit well with little mod....
thanx
later
HOW DID YOU MOUNT THE CONE ONTO THE FLOW METER LIKE THAT...IT HAS A SQUARE OPENING....
Yeah , i ment a cold air intake....but i'm just trying to throw the cone filter on now...
i'm making a custom cai..but it will take me a while to get the supplies i need...i'm making it with a short civic intake tube or a weapon r.....because both can fit well with little mod....
thanx
later
Last edited by jeremy; November-21st-2002 at 05:25 PM.
#6
where can i get this toyota filter adapter??....
I DON'T HAVE ANY PICS OF THE CAI...OR MY ENGINE BECAUSE I DON'T KNOW HOW TO POST THE PICS I HAVE...AND I HAVEN'T EVEN COME UP WITH A "FOR SURE" WAY TO DO THIS MOD...(CAI)
I'VE TAKEN ALOT OF PICS W/ A DIGITAL...I'D BE HAPPY TO SHARE...JSUST TELL ME HOW I POST THE PICS ON HERE..
LATER
I DON'T HAVE ANY PICS OF THE CAI...OR MY ENGINE BECAUSE I DON'T KNOW HOW TO POST THE PICS I HAVE...AND I HAVEN'T EVEN COME UP WITH A "FOR SURE" WAY TO DO THIS MOD...(CAI)
I'VE TAKEN ALOT OF PICS W/ A DIGITAL...I'D BE HAPPY TO SHARE...JSUST TELL ME HOW I POST THE PICS ON HERE..
LATER
#8
Here is a pic of a short ram intake on my 91 LX. Hope it's of some help.
http://www.imagestation.com/picture/...5.jpg.orig.jpg
Adam
91 LX
http://www.imagestation.com/picture/...5.jpg.orig.jpg
Adam
91 LX
#10
here's my take on the intake
all custom (more stuff on my site, a link is below in my sig)
and here's what you can't see down in the fender
Don't be fooled by the $9.99 crap on ebay for the adapters, they look like sheet and usually don't fit. You need a good seal and a cheap ***, made in 10 mins POS adapter, is not going to do that. JMHO
Oh, not to sound like a dick dude, but how the hell did you expect the ECU to know how much air is coming into the engine? There has to be an air:fuel ratio and if the ECU "see's" no air....then it doesn't provide the fuel either, even though there is obviously air going to the engine via the intake, the ECU has no idea since the air sensor is gone.... that make sense to you?
all custom (more stuff on my site, a link is below in my sig)
and here's what you can't see down in the fender
Don't be fooled by the $9.99 crap on ebay for the adapters, they look like sheet and usually don't fit. You need a good seal and a cheap ***, made in 10 mins POS adapter, is not going to do that. JMHO
Oh, not to sound like a dick dude, but how the hell did you expect the ECU to know how much air is coming into the engine? There has to be an air:fuel ratio and if the ECU "see's" no air....then it doesn't provide the fuel either, even though there is obviously air going to the engine via the intake, the ECU has no idea since the air sensor is gone.... that make sense to you?
#11
yeah it makes plenty of sense........
oh and whats up with all those ****** seals on your intake tube...
did you cut a peice of pipe to make it fit....why don't you give me some tips then so i can do this project on my own instead of spending money for an EIP TUNNING intake tube...
thanks
later
oh and whats up with all those ****** seals on your intake tube...
did you cut a peice of pipe to make it fit....why don't you give me some tips then so i can do this project on my own instead of spending money for an EIP TUNNING intake tube...
thanks
later
#12
well for starters, if you have been looking at the EIP intake, and it comes in peices, then you should be familiar with the extra ******* couplings, of which on mine, there is only one.
Yes, i cut a U bend pipe from JC Whitney to fit. You didn't ask for tips on buidling an intake, but how to bypass the VAF, but i did direct you to my website for tips...you did go there, didn't you?
If not then here are the 2 pages i have for my intake.
http://www.automediazone.com/pro/intake_TB-VAF.htm
http://www.automediazone.com/pro/CA_intake.htm
Yes, i cut a U bend pipe from JC Whitney to fit. You didn't ask for tips on buidling an intake, but how to bypass the VAF, but i did direct you to my website for tips...you did go there, didn't you?
If not then here are the 2 pages i have for my intake.
http://www.automediazone.com/pro/intake_TB-VAF.htm
http://www.automediazone.com/pro/CA_intake.htm
#13
Originally posted by mazdaspeedwest
well for starters, if you have been looking at the EIP intake, and it comes in peices, then you should be familiar with the extra ******* couplings, of which on mine, there is only one.
<snip>
well for starters, if you have been looking at the EIP intake, and it comes in peices, then you should be familiar with the extra ******* couplings, of which on mine, there is only one.
<snip>
#15
Originally posted by Davard
Hey Darryl. Are you sure you're not Jesse? Did you just quit smoking and give up caffeine? You're being awfully harsh with this idjut. Or is there something between you two the rest of us don't know about?
Hey Darryl. Are you sure you're not Jesse? Did you just quit smoking and give up caffeine? You're being awfully harsh with this idjut. Or is there something between you two the rest of us don't know about?
maybe i read his post with the wrong atitude...
Jeremy,
no hard feelings bro....
PS, If i was posessed by Jesse, you need a bigger flame suit than that...... muwaahaahaahaaaaaa
Thread
Thread Starter
Forum
Replies
Last Post
knightrider
1st gen/323/GLC Engine and Drivetrain
3
October-20th-2002 12:18 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)