Mazda 3 Cruise Control?
Hello, I am new to this site and I have just recently purchased a used 2008 Mazda 3. Even though it doesn't have power windows or doors, that doesn't really bother me. The biggest thing to me is not having cruise control. I was just wondering if there is a way to put one in and about how complicated it is to put it in? Thanks to anyone who is able to help me, I hope to learn a lot from this site about my new Mazda 3.
|
As long as you have a drive by wire throttle (if you're in the US or North America then you definitely do) then it's easily added. You need to get the brake switch for the cruise, and replace the steering wheel controls with the ones that have cruise on them. You do have to remove the airbag to change those out, but from what I've read it's actually really easy.
You might be able to find the parts in a junkyard for cheap. New I think they run about $125 together. The walkthrough I quoted below notes a different p/n, but I'm pretty sure for all '07+ models these ones are the correct parts as there was a change between '06 and '07. BS3E-66-4MO SWITCH, STEERING WHEEL W/CRUISE BN7N-66-490 SWITCH, BRAKE, W/CRUISE Here's an installation walkthrough copied from another forum. http://home.cogeco.ca/~tguertin/mazda3/cruise/parts.jpg Tools Required: Time Required: Procedure 1. Orient the steering wheel so that the wheels of the vehicle are positioned to move in straight line. 2. Disconnect the negative terminal of the car Battery using a 10mm socket; 3. Open the headlight switch and pump the brake pedal a few times to help drain any power left in the circuit. 4. Wait enough to make sure that any capacitive load in the electrical circuit had some time to be drained out before removing the airbag (2-3 hours? maybe not necessary, but why take a chance??) Use that time to swap the brake switch: 5. Brake Switch Replacement a. Locate the switch right above the brake pedal as shown. b. Disconnect the electrical connector by pressing on the release tab; c. To remove the switch, twist it like an 1/8 of a turn as shown, then pull it out; http://home.cogeco.ca/~tguertin/mazd...ake_switch.jpg d. Apply reverse procedure to install the new switch. 6. Airbag Removal (Please read disclaimer above!!! Again, I higly recomment you have a dealership or a competent garage do the part of the install involving the airbag. Improper handling or a static discharge could set it off resulting in expensive damage, injury or even death. I do not pretend that the procedure explained here is adequate or complete to remove & re-install the airbag.): a. Remove the 2 rubber plugs on each side of the steering wheel body, as shown below; http://home.cogeco.ca/~tguertin/mazd...rbag_bolts.jpg b. Using a 10mm socket, remove the 2 bolts holding the airbag in place; c. Pull the airbag assembly out carefully; d. Disconnect the electrical connectors of the airbag assembly: there are 2 connectors to disconnect. Pull the black locking tab using a small flathead screwdriver then pull the connector as shown; http://home.cogeco.ca/~tguertin/mazd...ise/airbag.jpg e. Safely store away (face up) the airbag until you ready for re-assembly. 7. Steering Wheel Removal a. Disconnect the wires of the steering switches; b. Using a 13/16" socket, remove the bolt clamping the steering wheel; c. Once the bolt removed, the steering wheel should pull out easily (I did not need a puller). 8. To replace the switch panels, you need to remove the back cover of the steering wheel. 2 screws must be removed from the back, then release the 2 tabs from the front side. http://home.cogeco.ca/~tguertin/mazda3/cruise/back.jpg 9. Remove the old switch panels on either sides of the steering wheel and replace them with the new switch modules. They are held by a screw from the back side of the steering wheel. Pay attention to how the wires are routed and use the same approach for the new switches. http://home.cogeco.ca/~tguertin/mazda3/cruise/done.jpg 10. Carefully re-assemble everything using reverse procedure, re-connect the battery and go for a test drive to verify that everything is working properly. Enjoy! |
great writeup
|
Thanks for that, I'm sure it will come in handy when I get the parts. Thanks a lot.
|
does this work on the 2011 Mazda3 isport. If someone has or knows someone with a 2011 mazda3, and has done this please let me know, cause all i can find is parts for 2010 models and older. I am assuming the 2007-2010 all would work, from what i have gathered from the threads, but I want to make sure before I dump $160+ on it!
Thanks! |
Originally Posted by Daark08
(Post 414743)
does this work on the 2011 Mazda3 isport. If someone has or knows someone with a 2011 mazda3, and has done this please let me know, cause all i can find is parts for 2010 models and older. I am assuming the 2007-2010 all would work, from what i have gathered from the threads, but I want to make sure before I dump $160+ on it!
Thanks! |
Confirmed. This worked for me on my 2004 Mazda 3 2.3
Alex |
Thanks for the write-up, when talking with Mazda about installing this they told me that I would need to have the car hooked up to a programmer, Is this nessesary, or a dealership just looking for extra money?
I have an 05 Mazda 3 i |
Dealership wanting more money. Just replace the two parts as noted above and it will work.
|
I have a '06 Mazda 3. My cruise won't engage. Is that a brake switch problem?
|
Problem with cruise control
Hi
I'm new around here Did everything step by step on my car, but cruise does not work :dunno: Anyone knows if u have to do anything else? i have a 2008 2.0 Automatic M3 Thanks a lot |
cruise control
Originally Posted by ccre72
(Post 422410)
Hi
I'm new around here Did everything step by step on my car, but cruise does not work :dunno: Anyone knows if u have to do anything else? i have a 2008 2.0 Automatic M3 Thanks a lot I have the same problem. I did everything but is not working... |
Will this work for a 2013 Mazda 3 SV which did not come with cruise control?
|
Hello I have a Mazda 3 year 2006 I want to add control from the steering wheel to a p
Originally Posted by Ramenstien
(Post 414431)
Hello, I am new to this site and I have just recently purchased a used 2008 Mazda 3. Even though it doesn't have power windows or doors, that doesn't really bother me. The biggest thing to me is not having cruise control. I was just wondering if there is a way to put one in and about how complicated it is to put it in? Thanks to anyone who is able to help me, I hope to learn a lot from this site about my new Mazda 3.
|
would that also work in a MPS bk? the stering wheels switch and the brake switch for the cruise control?
|
All times are GMT -5. The time now is 11:53 PM. |
© 2024 MH Sub I, LLC dba Internet Brands